行業資訊
聯系我們
濟南福華建材廠
聯系人:吳老師
電話:13864111871
手機:13864111871
0531-81901300
地址:山東省濟南市高新開發區巨野河辦事處山圈村西
膩子粉表面泛黃的主要因素
來源:http://www.bjtsdc.com 日期:2023-03-10 發布人:
1冤荆、灰鈣粉反堿引起泛黃
1. Yellowing caused by alkali reaction of lime and calcium powder
灰鈣粉主要成分氫氧化鈣扔役,分子式Ga(OH)2,相對分子量74卫病,熔點5220油啤,PH值≥12,逞強堿性膏娃,白色細膩粉末狀党纱,微溶于水,能溶于酸蚜再、甘油豹恶、糖、氯化銨中率敞,溶于酸中釋放大量熱量旅峰,相對密度為2.24滞逼,其澄清水溶液為無色無嗅的堿性透明液體,置于空氣中逐漸吸收念距,氧化鈣變成碳酸鈣泄肆。
The main component of gray calcium powder is calcium hydroxide, molecular formula Ga (OH) 2, relative molecular weight 74, melting point 5220, PH value ≥ 12, extremely alkaline, white and fine powder, slightly soluble in water, soluble in acid, glycerin, sugar, ammonium chloride, soluble in acid, release a lot of heat, relative density 2.24, its clear water solution is colorless and odorless alkaline transparent liquid, which is gradually absorbed in the air, and calcium oxide becomes calcium carbonate.
氫氧化鈣屬中強堿性,其堿性及腐蝕性要比氫氧化鈉弱董容,氫氧化鈣及其水溶液無毒鹤协,但對人的皮膚、衣物等有腐蝕性衍震,不能長時間直接與皮膚接觸味滞。氫氧化鈣在耐水膩子中屬活性填料與重質碳酸鈣、膩子粉生成硬性膜钮呀,由于其堿性較強剑鞍,堿的含量較大。
Calcium hydroxide is moderately alkaline, and its alkalinity and corrosivity are weaker than sodium hydroxide. Calcium hydroxide and its aqueous solution are non-toxic, but they are corrosive to human skin, clothing, etc., and cannot be in direct contact with skin for a long time. In water-resistant putty, calcium hydroxide is an active filler and forms a hard film with heavy calcium carbonate and putty powder. Because of its strong alkalinity, its alkali content is large.
在施工時行楞,膩子中的部分水分會被墻基層同樣強堿性的水泥砂漿底攒暇、或砂灰底(石灰土匀、砂子房、少量水泥)所吸收,隨著膩子層逐漸干燥就轧、水分的揮發证杭,基層砂漿和膩子中的堿性物質和一些水解后不穩定物質(如二價鐵、三價鐵等)會通過膩子的微細孔折出妒御,遇空氣后產生化學反應解愤,引起濟南膩子粉表面泛黃。
During construction, part of the moisture in the putty will be absorbed by the cement mortar bottom with the same strong alkalinity of the wall base, or the sand-gray bottom (lime, sand, a small amount of cement). With the gradual drying of the putty layer and the volatilization of the moisture, the alkaline substances in the base mortar and putty and some unstable substances after hydrolysis (such as ferrous iron, ferric iron, etc.) will be broken out through the tiny holes of the putty, which will produce chemical reaction after meeting the air, causing the surface of Jinan putty powder to turn yellow.
2乎莉、易揮發性有機化學氣體送讲。如一氧化碳(CO)、二氧化硫(SO2)炒圈、苯署咸、甲苯、二甲苯蚕顷、甲醛铜乱、煙火等。在一些工程案例中峰辣,呈出現在剛刮完奶水妮子的房間內使用油漆或生火取暖馏舰、甚至是在房間內燒香、多人同時吸煙等情況而引起膩子表面泛黃拓坠。
2. Volatile organic chemical gas. Such as carbon monoxide (CO), sulfur dioxide (SO2), benzene, toluene, xylene, formaldehyde, fireworks, etc. In some engineering cases, the putty surface turns yellow due to the use of paint or fire for heating in the room where the putty has just been shaved, or even burning incense in the room, or many people smoking at the same time.


3便浮、氣候環境因素的影響哩拒。在北方地區,季節交換期胆快,一般在11月份至第二年5月份有過膩子表面泛黃煞陵,但只是個別現象。
3. The impact of climate and environmental factors. In the northern region, the putty surface turns yellow from November to May of the next year during the seasonal exchange period, but only a few phenomena.
4烁焙、通風干燥狀況不好航邢。墻體潮濕,刮完耐水膩子后骄蝇,在膩子層未全干燥的情況下膳殷,長時間緊閉門窗,也容易引起膩子表面泛黃九火。
4. The ventilation and drying conditions are not good. When the wall is wet and the waterproof putty is scraped, the door and window will be closed for a long time when the putty layer is not completely dry, which is also easy to cause the putty surface to turn yellow.
5赚窃、基層問題。老墻底一般都是砂灰墻(石灰岔激、啥子勒极、少量水泥,有的還慘有石膏)虑鼎,這類墻基層強度低辱匿、吸水率高、易粉化炫彩,而新墻底是以水泥砂漿為主匾七,但還有不少地區在用石灰、石膏抹墻江兢∥鄣樱基層墻體中的材料大多呈堿性,膩子接觸墻體后昙激,一些水分會被墻體吸入狰娱,通過水解、氧化后赤猾,有部分物質劈耽,如堿、鐵等堵生,會通過墻體微細孔折出來嘁梦,遇空氣后產生化學反應,引起膩子表面泛黃钾士。
5. Grassroots issues. The bottom of the old wall is generally sand-sand wall (lime, sand, a small amount of cement, and some have gypsum). This kind of wall base has low strength, high water absorption, and is easy to pulverize. The new wall bottom is mainly made of cement mortar, but there are still many areas where lime and gypsum are used to plaster the wall. Most of the materials in the base wall are alkaline. After the putty contacts the wall, some water will be absorbed by the wall. After hydrolysis and oxidation, some substances, such as alkali and iron, will be broken out through the wall micro-holes, which will produce chemical reaction after meeting the air, causing the putty surface to turn yellow.
除上述可能因素外滩蔼,還會有其他因素的影響,這需要進一步探討应揉。當然您對膩子粉有需求粥搓,可以隨時來我們網站http://www.bjtsdc.com進行咨詢了解洞枷!
In addition to the above possible factors, there will be other factors, which need further discussion. Of course, if you need putty powder, you can come to our website at any time http://www.bjtsdc.com Consult and understand!
