作為墻面施工必不可少的一道工序抹缕,如果膩?zhàn)訉拥氖┕ばЧ霈F(xiàn)問題,外飾面層整體效果將大打折扣。在如此環境下施工,可能會面臨的問題是什么?為了不讓環境影響
掉粉韵披、脫層
Powder shedding and delamination
施工完成及干透后失臂,用手觸摸有掉粉現象,嚴重的甚至出現前后兩道膩?zhàn)又g或膩?zhàn)优c基底之間相互剝離镇锣。
After the construction is completed and dried thoroughly, there is a phenomenon of powder falling when touched by hand, and in severe cases, there may even be peeling between the front and rear layers of putty or between the putty and the substrate.
【原因】膩?zhàn)釉诟邷馗稍飼r(shí)施工权洼,水分揮發快,沒有足夠水分進行固化一宁,因而容易脫粉献蛔。而底層膩?zhàn)邮杷煞刍瘒?yán)重,面層膩?zhàn)犹簿嗷荆稍锾鞎?huì)造成脫層允瞧。另外,外墻膩?zhàn)颖挥晁疀_刷后,粘結劑流失蛮拔,重批后也容易脫層述暂。
【 Reason 】 Putty is applied at high temperatures and dryness, and the moisture evaporates quickly. There is not enough moisture to cure, so it is easy to remove powder. The bottom layer of putty is loose and severely powdery, while the surface layer of putty is too hard and dries too quickly, which can cause delamination. In addition, after the external wall putty is washed away by rainwater, the adhesive is lost, and it is also easy to delaminate after re approval.
【解決方法】高溫、干燥強風天氣施工建炫,好將基面潤濕無明水后再進行膩?zhàn)邮┕て杈隆J┕r(shí)要收壓密實,適度掌握干燥時間肛跌。處理起來具體情況具體分析:
【 Solution 】 For construction in high temperature, dry and strong wind weather, it is recommended to wet the base surface without open water before applying putty. During construction, it is necessary to compact and control the drying time appropriately. Analyze the specific situation when dealing with it:
1廊驼、內墻耐水膩?zhàn)油窟^(guò)封閉底漆后,強度會增加惋砂,一般無需另行處理妒挎。
1. After applying sealing primer to the waterproof putty of the inner wall, the strength will increase and generally does not require additional treatment.
2、外墻膩?zhàn)討?yīng)嚴格執行保濕施工西饵,避免陽光直射施工酝掩,面層膩?zhàn)颖砀珊蠹皶r(shí)適度打磨并充分淋水2次以上。
2. The external wall putty should strictly follow the moisturizing construction to avoid direct sunlight. After the surface layer of putty is dry, it should be timely and moderately polished and thoroughly watered for at least 2 times.
3眷柔、壓光膩?zhàn)颖砻鎽?yīng)再薄批膩?zhàn)右坏榔迦⒓皶r(shí)進行壓光處理。
3. The surface of the polished putty should be thinly coated with another layer of putty, and the polishing treatment should be carried out in a timely manner.
夏季高溫膩?zhàn)臃凼┕さ淖⒁馐马?xiàng)相關內容就講解到這里了允纬,還有什么問題咨詢了解就來我們網站
http://www.bjtsdc.com看看吧铜部!
That's all we need to know about the precautions for high-temperature putty powder construction in summer. If you have any further questions, please come to our website for consultation and understanding http://www.bjtsdc.com Take a look!