濟南福華建材廠
聯系人:吳老師
電話:13864111871
手機:13864111871
0531-81901300
地址:山東省濟南市高新開發區巨野河辦事處山圈村西
如何用膩?zhàn)臃圻M(jìn)行補墻欣硼?
來源:http://www.bjtsdc.com 日期:2024-04-11 發布人:
1纳像、墻面清理
1. Wall cleaning
在用膩?zhàn)臃垩a(bǔ)墻時,我們可以使用鏟刀將脫落唆铐、粉化的膩?zhàn)訉隅P掉哲戚,并把墻面上粉塵清理干凈。如果墻面出現大范圍的墻皮脫落等問題艾岂,那么需要將墻面上的膩?zhàn)訉佣肩P掉顺少,通過重新批刮膩?zhàn)拥姆绞竭M(jìn)行修補。在批刮膩?zhàn)忧耙猿啵蠹铱稍趬γ嫔贤克⒁粚咏缑鎰┛牧眩欣谀佔雍蛪w間的粘接。
When repairing walls with putty powder, we can use a shovel to remove the loose and powdery putty layer and clean the dust on the wall. If there is a large-scale peeling of the wall surface, it is necessary to scrape off the putty layer on the wall and repair it by reapplying the putty. Before applying putty, you can apply a layer of interface agent on the wall to facilitate the adhesion between the putty and the wall.
2劣饺、膩?zhàn)臃叟渲?/p>
2. Putty powder preparation
我們往攪拌桶中倒入適量的膩?zhàn)臃塾」茫偬砑忧逅M(jìn)行攪拌。通常膩?zhàn)臃酆退前凑?:0.5的比例進行配置的契片,具體的比例要查看產品說明書狮贪。用電動攪拌機將膩?zhàn)臃蹟嚢杈鶆蛑螅覀冃鑼⑵潇o置十幾二十分鐘汛欺,這樣有利于膩?zhàn)臃壑械幕瘜W(xué)成分溶解尾杆。膩?zhàn)臃垤o置好后设塑,再將其攪拌均勻才能使用。
We pour an appropriate amount of putty powder into the mixing bucket, and then add water for stirring. Usually, putty powder and water are prepared in a ratio of 1:0.5, and the specific ratio should be checked in the product manual. After using an electric mixer to mix the putty powder evenly, we need to let it stand for ten to twenty minutes to facilitate the dissolution of the chemical components in the putty powder. After the putty powder is left to stand, mix it evenly before use.
3狗丙、墻面修補
3. Wall repair
我們將配置好的膩?zhàn)佑霉伟鍖⑵渫磕ㄔ趬γ嫘栊扪a(bǔ)處譬奈,如果我們需涂刷的膩?zhàn)訉颖容^厚,可以分兩到三次批刮膩?zhàn)舆M(jìn)行修補暇昂,每遍膩?zhàn)拥耐克⒑穸仍?.5毫米左右莺戒。等到第一遍膩?zhàn)痈稍镏螅覀冇蒙凹垖⒛佔訉哟蚰ズ眉辈ā=酉聛?lái)按照相同的方法批刮第二遍膩?zhàn)哟硬谌槟佔印4蠹也荒茉谀佔游锤芍熬驮俅闻文佔俞Q隆γ婢植啃扪a(bǔ)過的膩?zhàn)訉有枰瓉?lái)墻面膩?zhàn)訉颖3制秸?/p>
We will use a scraper to apply the prepared putty to the areas that need to be repaired on the wall. If the putty layer we need to apply is relatively thick, we can divide it into two to three batches of putty for repair. The thickness of each batch of putty application is about 0.5 millimeters. After the first layer of putty dries, we use sandpaper to polish the putty layer well. Next, apply the second layer of putty and the third layer of putty using the same method. You cannot reapply putty before it dries. The putty layer that has been partially repaired on the wall needs to be kept flat from the original wall putty layer.
手機站
關注微信公眾號